Key takeaways
- A main-lug-only 6 circuit sub panel suits a homeowner adding a small number of branch circuits to a garage, shed, or workshop fed from an existing main…
A main-lug-only 6 circuit sub panel suits a homeowner adding a small number of branch circuits to a garage, shed, or workshop fed from an existing main panel, while a main-breaker-equipped 6 circuit panel suits a feed that needs its own disconnect, such as a detached structure fed by a longer run of wire. Either way, a sub panel this small is a job for a licensed electrician to size and install correctly, since panel selection depends on local code, the feeder wire and breaker sizing upstream, and the specific loads being added.
What a 6 Circuit Sub Panel Actually Is
A sub panel is a secondary load center fed from a main panel (or sometimes from a generator transfer setup) rather than directly from the utility meter. A “6 circuit” rating refers to the number of single-pole breaker slots, so a 6-space panel can typically hold 6 single-pole breakers, or fewer slots if some are filled with double-pole (240V) breakers, since those occupy two spaces each. These small panels are common for workshops, detached garages, small additions, well pumps, or as a dedicated panel for a handful of circuits like a generator-backed subset of a home’s loads.
Panels in this category are generally sold as either “main lug only” (MLO), meaning there’s no single disconnect for the whole panel and each breaker is fed directly from the lugs, or with a main breaker built in, which adds a single disconnect point for the entire panel. Code requirements for when a main breaker is required (for example, based on the number of disconnects or the distance and location of the panel) vary by jurisdiction, which is one of several reasons a licensed electrician should confirm panel type before purchase.
What to Check Before Buying
- Bus bar amperage rating: common small sub panels are rated around 100A or less on the bus, separate from the feeder breaker that protects the panel upstream; the panel’s rated amperage must be matched to the feeder size by a qualified installer, not guessed.
- Indoor vs. outdoor rating: panels installed outside or in damp locations need a weatherproof/rainproof-rated enclosure; an indoor-rated panel is not a substitute.
- Breaker compatibility: sub panels are generally only compatible with breakers from the same manufacturer’s listed line (common manufacturers of residential load centers include Square D, Eaton, Siemens, and GE); mixing incompatible breaker brands is a recognized safety hazard and is not code-compliant in most jurisdictions.
- Main breaker vs. main lug only: confirm with a licensed electrician which configuration your installation requires based on local code and the specific feed setup.
- Grounding and bonding hardware: sub panels generally require a separate (not bonded) neutral and ground bar setup, unlike a main panel; the maker’s included hardware and the installer’s wiring must match code for sub panel grounding.
- Physical size and knockouts: confirm the panel’s dimensions and conduit knockout locations fit the installation space and the wiring method planned (conduit, cable, etc.).
At a Glance
| Panel type | Best for | Typical stated specs | Limits |
|---|---|---|---|
| Main lug only (MLO), indoor | Adding circuits where a separate disconnect isn’t required by code | 6-space bus, bus rating commonly up to 100A, indoor NEMA enclosure | No built-in disconnect; upstream breaker serves that function |
| Main breaker panel, indoor | Installations needing a dedicated on-site disconnect | 6-space bus plus a main breaker slot (reduces available branch spaces), indoor enclosure | Larger enclosure than MLO for the same branch space count |
| Outdoor/weatherproof rated panel | Detached garages, sheds, or any outdoor feed point | Rainproof or weatherproof enclosure rating, corrosion-resistant hardware | Higher cost than an equivalent indoor-rated panel |
| Generator-ready sub panel | Backing up a defined subset of circuits during an outage | Designed to pair with a transfer switch or interlock kit from the same product line | Only compatible with the specific transfer hardware the maker lists for it |
Pick-X Decision Table
| If your installer specifies… | Pick |
|---|---|
| No separate disconnect is required at the sub panel location | A main-lug-only panel |
| A dedicated on-site disconnect is required | A main-breaker-equipped panel |
| The panel will be mounted outside or in a damp area | A weatherproof/rainproof-rated enclosure |
| The panel will back up specific circuits during outages | A generator-ready panel matched to the planned transfer switch or interlock |
| Breakers from a specific existing panel brand need to match | A sub panel listed as compatible with that same manufacturer’s breaker line |
Code and Safety Notes
Electrical panel work, including selecting and installing a sub panel, is regulated under the National Electrical Code (NEC) in the US along with local amendments, and most jurisdictions require a permit and inspection for sub panel installations. Improperly bonded neutrals, mismatched breakers, or incorrect feeder sizing are recognized fire and shock hazards. This guide is for general orientation only; follow the manufacturer’s installation instructions and have the work performed or verified by a licensed electrician who can confirm load calculations, wire sizing, and code compliance for your specific jurisdiction and installation.
A Few Reasonable Alternatives
- 8 or 12 circuit sub panels: for installations that may need more branch circuits than 6 slots allow, a larger panel from the same product line avoids a future panel swap.
- Combination meter/main/sub panel setups: some detached structures use a combined meter socket and small panel rather than a standalone sub panel fed from the main house panel; which setup applies depends on the utility’s and local code’s rules for the specific property.
- Transfer-switch-integrated panels: for homeowners planning generator backup from the start, a panel designed around a specific transfer switch or interlock kit can simplify that future installation compared to retrofitting a standard sub panel later.
Frequently Asked Questions
Can I install a 6 circuit sub panel myself?
In many jurisdictions, panel work requires a licensed electrician and a permit, and even where a homeowner is legally permitted to do the work, incorrect sizing or wiring creates a real fire and shock hazard. Consulting a licensed electrician before purchase ensures the panel, feeder, and breakers are matched correctly to your specific installation.
What’s the difference between main lug only and main breaker panels?
A main-lug-only panel has no single on/off switch for the whole panel; each breaker connects directly to the incoming feed through the lugs. A main-breaker panel adds one breaker that can disconnect the entire panel at once, which some installations require by code depending on disconnect location and count.
Can I mix breaker brands in a sub panel?
No. Panels are generally only listed and rated for use with breakers from the same manufacturer’s compatible line, and using mismatched breakers is widely considered a safety hazard as well as a code violation in most areas. An electrician can confirm which breaker line matches a specific panel.
Does a sub panel need its own ground rod?
Requirements vary by installation type, particularly for detached structures, and this is specifically the kind of question a licensed electrician should answer based on local code and the structure’s wiring method. Sub panels do generally require separated neutral and ground bars rather than the bonded arrangement used in a main panel.
How do I know what amperage sub panel I need?
Amperage sizing depends on a load calculation covering the circuits the sub panel will feed and the capacity of the feeder wire and breaker supplying it from the main panel. This calculation should be performed by a licensed electrician rather than estimated, since undersizing creates an overload risk and oversizing can waste budget on unnecessary capacity.
Is an outdoor-rated panel required for a detached garage or shed?
If the panel itself will be mounted outdoors or in a location exposed to moisture, a weatherproof or rainproof-rated enclosure is typically required; an indoor panel mounted inside a detached but enclosed garage may not need the outdoor rating. Confirming the specific location and local code requirements with an electrician before purchase avoids buying the wrong enclosure type.
Further reading
- Best Fiber Patch Panel Enclosure: Picks and What to Look For (2026)
- Best Circuit Breaker Trip Tester: Picks and What to Look For (2026)
- Best Goalie Gloves: Picks and What to Look For (2026)
- Best Blue Sea Power Distribution Block: Picks and What to Look For (2026)
- Best 100 Amp Gas Generator: Picks and What to Look For (2026)
- Best Hepa Solder Fume Extractor: Picks and What to Look For (2026)